Grade 5 Titanium in ASTM B338
ASTM B338 covers seamless and welded titanium tubes for condensers and heat exchangers, and it lists Grade 5 as an approved alloy. Grade 5, designated UNS R56400, contains 5.5 to 6.75 percent aluminium and 3.5 to 4.5 percent vanadium, with the balance titanium. It is an alpha-beta alloy that develops a minimum tensile strength of 895 MPa and a minimum yield strength of 828 MPa in the annealed condition, roughly 2.5 times the strength of Grade 2 commercially pure titanium.
The specification controls chemistry tightly, including oxygen limited to 0.20 percent, and requires mechanical testing, hydrostatic or non-destructive examination, and dimensional verification on each lot. Tube is supplied in diameters and wall thicknesses matched to heat exchanger design, with straight lengths typically from 3 to 12 metres and tolerances defined in the standard.
Why a High-Strength Tube Is Needed
Heat exchanger design is governed by pressure, temperature and the mechanical loads of installation. Grade 5 tubing lets designers use a thinner wall for a given design pressure than a commercially pure grade, which improves heat transfer and reduces material weight. In high-pressure feedwater heaters and boiler economisers, where internal pressure can reach tens of bars, the higher allowable stress of Grade 5 translates into compact bundles and lower shell costs.
Fatigue is the second driver. Thermal cycling between operating and shutdown conditions, plus flow-induced vibration, imposes alternating stress on the tube. The high fatigue endurance of Ti-6Al-4V gives designers a larger safety margin against vibration failure, which is why the alloy is specified in demanding services where premature tube failure would force an expensive shutdown.
Corrosion Behaviour in Boiler and Cooling Service
Titanium tubes resist general corrosion in boiler feedwater, condensate and treated cooling water, and the oxide film protects against pitting in chloride-bearing waters that attack stainless steel. Grade 5 retains this resistance in most neutral and oxidising environments, though the higher alloy content makes it less forgiving than pure titanium in some hot reducing acids, so water chemistry control remains important.
In seawater-cooled exchangers, titanium tubes eliminate the corrosion allowances and coatings required by copper-nickel or steel. Erosion by suspended solids is low because the hard, smooth oxide surface resists particle impingement. The practical result is a tube that rarely fails from corrosion, allowing the design life of the exchanger to be set by mechanical rather than corrosion considerations.
Fabrication and Installation Considerations
Grade 5 tube is less formable than commercially pure grades, so rolling into tube sheets and bending require adjusted practice. Tube end rolling uses mandrel control and carefully selected expansion to avoid work hardening cracks, and tight radius bends are made with rotary draw equipment. Welding for tube-to-tubesheet joints is done with gas tungsten arc welding under inert gas, with filler metal selected to match the alloy.
Heat treatment after forming is generally not required, but heavy cold work followed by service in critical applications may call for stress relief. The tube is handled with non-metallic slings and clean gloves because iron contamination can cause localised corrosion at elevated temperature; pickling or cleaning removes any embedded iron before service.
Quality Control and Certification
Each lot of Grade 5 tube carries a material test certificate confirming chemistry, tensile properties, flattening and flaring performance, and non-destructive examination results. Eddy current or ultrasonic testing checks the full length for defects, and hydrostatic testing verifies pressure integrity where required. The documentation trail lets the exchanger fabricator trace every tube to its melt, which is essential for code compliance and insurance requirements.
For boilers and heat exchangers following ASME Section VIII or similar codes, the tube producer's certification is reviewed against the design specification before installation. This disciplined chain of control is the reason titanium tubing performs reliably for decades in the most severe heat exchange duties.
Frequently Asked Questions
Q: What is the strength of ASTM B338 Grade 5 titanium tube?
A: Annealed Grade 5 tube has a minimum tensile strength of 895 MPa and a minimum yield strength of 828 MPa, which is about 2.5 times the strength of Grade 2 titanium.
Q: Why use Grade 5 instead of pure titanium in heat exchangers?
A: The higher allowable stress permits thinner walls for the same pressure, improving heat transfer and reducing weight, while fatigue resistance protects against vibration and thermal cycling failures.
Q: Does Grade 5 titanium tube resist seawater corrosion?
A: Yes, the stable oxide film resists pitting and erosion in seawater and chloride-bearing waters, which is why the alloy is used in marine cooling exchangers.
Q: Can Grade 5 tube be rolled into tube sheets?
A: Yes, but the rolling expansion must be controlled carefully because the alloy is stronger and less ductile than pure titanium; proper mandrel control prevents cracking.
Q: Is post-weld heat treatment required for Grade 5 tube joints?
A: Not normally. Welds made with matching filler and proper inert gas shielding meet design requirements without post-weld heat treatment in most heat exchanger services.





