Grade 38 at a Glance: The Iron-Bearing Alternative
Grade 38 is an alpha-beta titanium alloy with nominal composition Ti-4Al-2.5V-1.5Fe-0.25O, listed under UNS R55380. Its engineering purpose is straightforward: by substituting iron for part of the vanadium used in Ti-6Al-4V, the alloy delivers comparable tensile strength at lower raw material cost, because iron is a cheap and effective beta stabiliser while vanadium is not.
Bars and billets in this grade are specified under ASTM B348, and sheet and strip can be produced under the corresponding wrought product specifications. The commercial significance of the alloy is that it can be both hot and cold worked, so it is available as thin sheet, coil, strip, precision hot-drawn strip, heavy plate, seamless tube and cast or engineered product forms - a wider range than is normally offered for a high-strength titanium alloy.
Nominal Composition and Phase Transformation Temperature
The nominal analysis below is expressed as the alloy is commonly described in technical literature. Acceptance limits for a specific order are those stated in the applicable product specification for the grade.
| Element | Nominal content | Role |
|---|---|---|
| Ti | Balance | Matrix |
| Al | 4.0 % | Alpha stabiliser, strength at temperature |
| V | 2.5 % | Beta stabiliser, retained in reduced quantity |
| Fe | 1.5 % | Low-cost beta stabiliser, controls strength |
| O | 0.25 % | Interstitial strengthener |
The beta transus of the alloy has been measured at approximately 970 °C, against about 995 °C for Ti-6Al-4V. That 25 degree difference matters in process design because it lowers the temperature at which the structure transforms, so every annealing window shifts downward accordingly. Iron also diffuses quickly, which makes the alloy sensitive to cooling rate in a way that vanadium-rich alloys are not.
Annealing Regimes and Resulting Properties
Production trials on bar product, using material melted twice under vacuum and forged and rolled to finished diameter, show that a one hour hold followed by different cooling rates gives distinctly different results. The four regimes below summarise the pattern that emerges from holding at 830, 930, 950 and 1000 °C with furnace cooling, air cooling or water quenching.
| Hold temperature | Cooling | Result | Best used for |
|---|---|---|---|
| 830 °C | Air | Low yield strength, high retained workability | Stock for subsequent forming or drawing |
| 930 - 950 °C | Air or water | High strength with good plasticity, best overall combination | Finished bar and structural parts |
| 1000 °C | Air | Coarser structure, shallower fracture dimples, reduced plasticity | Not recommended for ductility-critical parts |
The conclusion from that work is that holding at 930 to 950 °C for one hour followed by air cooling or water quenching produces the best combination of strength and plasticity in Grade 38. Annealing at 830 °C and air cooling gives noticeably lower yield strength, which is useful when the material still has to be machined or formed, but is not a finished-property condition. Holding at 1000 °C, above the transus, produces a coarser structure and measurably poorer ductility.
Microstructure, Fracture Behaviour and Process Control
Room-temperature tensile fractures in Grade 38 show the dimpled, honeycomb morphology characteristic of ductile failure. After annealing at 1000 °C the dimples become smaller and shallower, which is the fractographic signature of the reduced plasticity measured in tensile testing. This is a direct consequence of the coarse transformed structure formed above the beta transus, and it is why the transus temperature is treated as a process limit rather than a reference value.
Two control points follow. First, furnace uniformity and thermocouple accuracy must be good enough that the 930 to 950 °C window is genuinely held, since a 60 degree overshoot crosses into the coarse-structure regime. Second, cooling rate must be reproducible: air cooling, water quenching and furnace cooling produce different yield strengths, so the cooling method is part of the specification, not an operator choice.
Mechanical evaluation follows ASTM E8/E8M for tension testing, with microstructure assessed to ASTM E112 for grain size and heat treatment performed within the framework of AMS 2801 for titanium parts.
Supply Forms, Inspection and Applications
The combination of strength, cold workability and lower alloy cost makes Grade 38 attractive wherever a high-strength titanium alloy has to be supplied as thin or continuous product. Available forms include cold-rolled sheet and coil, precision strip, heavy plate, seamless tube and bar. The alloy is also used for superplastic forming, where its fine starting structure allows large strain at elevated temperature, and it is reported to be weldable by friction stir welding.
Because iron-rich titanium alloys can segregate during melting, incoming inspection should include chemical analysis of the finished product rather than relying solely on the ingot analysis, plus tensile testing per heat and lot and grain size measurement on a sample from the annealed product. Ultrasonic examination of bar and billet is normally performed to AMS 2631 or ASTM E2375.
Typical applications are aerospace structural and engine components, defence hardware, and replacement of heavier steel or lower-strength aluminium parts where weight reduction has to be achieved without sacrificing tensile strength. Open-hole fatigue performance and superplastic formability are the two properties most often cited when the alloy is selected over a conventional alpha-beta grade.
Frequently Asked Questions
Q: What is the nominal composition of Grade 38 titanium?
A: Ti-4Al-2.5V-1.5Fe-0.25O, under UNS R55380. Iron replaces part of the vanadium used in Ti-6Al-4V, which lowers cost while retaining comparable strength.
Q: What is the beta transus of Grade 38?
A: Approximately 970 °C, measured by elevated-temperature metallography. This is about 25 degrees lower than Ti-6Al-4V, so all annealing windows shift downward.
Q: Which annealing condition gives the best strength and ductility?
A: Holding at 930 to 950 °C for one hour and then air cooling or water quenching produces the best overall combination of high strength and good plasticity.
Q: Why is 1000 °C annealing avoided?
A: It is above the beta transus, so the structure coarsens. Tensile fracture surfaces show smaller, shallower dimples and the material loses plasticity, which is undesirable for ductility-critical parts.
Q: Does cooling rate matter after annealing?
A: Yes. Furnace cooling, air cooling and water quenching give measurably different yield strengths, so the cooling method must be specified and reproduced rather than left to shop practice.
Q: Can Grade 38 be cold worked?
A: Yes, which is one of its main advantages. It is supplied as cold-rolled sheet, coil, strip, precision hot-drawn strip, heavy plate and seamless tube, unlike many high-strength titanium alloys that are effectively limited to bar and forging stock.





