Mar 27, 2024 Leave a message

Common Uses of ASTM B862 Welded Titanium Tubing

Scope of ASTM B862

ASTM B862 covers welded titanium and titanium alloy tubing made from strip or sheet, with the weld seam produced by tungsten inert gas welding, plasma welding or high-frequency induction welding. The specification lists required chemical composition, tensile properties, flattening and flaring behaviour, and nondestructive examination of the weld. Grades covered range from commercially pure Grades 1 to 4 up to alloy grades such as Grade 9, Grade 12 and Ti-6Al-4V.

Because the tubing is produced from strip, it can be made in very long lengths with tight wall tolerances, which makes it economical for large surface-area equipment where the weld quality is verified by eddy current or ultrasonic examination.

Heat Exchange and Condenser Service

Welded titanium tubing is a standard choice for shell-and-tube heat exchangers and condensers in power plants, chemical plants and refineries. Titanium resists chloride pitting and stress corrosion cracking that would rapidly destroy copper-nickel or stainless steel tubes in seawater and brackish cooling water.

For this service the tube is ordered to the supplementary requirements of ASTM B338, which add flattening, flaring and hydrostatic testing appropriate for heat exchanger duty.

Chemical and Process Industry

In chemical processing, ASTM B862 tubing is used for heater bundles, evaporator coils, reboiler tubes and process piping carrying chlorides, oxidising acids and organic media. Commercially pure grades handle oxidising conditions, while palladium-bearing grades extend service into reducing acids such as dilute hydrochloric and sulphuric acid.

The long coil lengths reduce the number of welded field joints, which lowers installation cost and eliminates potential leak points in corrosive service.

Marine, Power and Desalination

Marine engineering uses welded titanium tubing for seawater cooling systems, firewater lines, offshore platform piping and ballast water treatment units. Power stations use titanium condenser tubing to avoid the repeated failures associated with other condenser tube alloys.

Desalination plants, particularly multi-stage flash and reverse osmosis systems, rely on titanium tube for brine heaters and heat recovery sections, where the combination of corrosion resistance and long service life outweighs the initial material cost.

Alloy Grades for Special Duty

When service demands strength above the commercially pure grades, Grade 9 tubing offers roughly double the yield strength of Grade 2 while remaining weldable, and it is used for high-pressure hydraulic and instrumentation lines. Grade 12 tubing adds molybdenum and nickel to improve resistance to hot brine and reducing environments, and it is a frequent choice for geothermal and chemical heat exchangers.

Ti-6Al-4V tubing appears where maximum strength-to-weight ratio is needed, such as aerospace fluid lines, provided the fabrication route controls the higher strength material correctly.

Frequently Asked Questions

Q: What is the difference between ASTM B862 and ASTM B338 tubing?

A: ASTM B862 is the general specification for welded titanium tubing, while ASTM B338 covers seamless and welded tube specifically for condensers and heat exchangers with additional testing requirements.

Q: Which titanium grades are covered by ASTM B862?

A: The specification covers commercially pure Grades 1 to 4 and a range of alloy grades including Grade 5, Grade 7, Grade 9, Grade 12, Grade 18 and Grade 23.

Q: Is welded titanium tubing suitable for seawater service?

A: Yes, welded titanium tube is widely used in seawater-cooled condensers and heat exchangers because of its resistance to chloride pitting and crevice attack.

Q: How is the weld quality of ASTM B862 tubing verified?

A: The weld is examined by eddy current or ultrasonic methods, and the tube must pass flattening and flaring tests that exercise the weld zone.

Q: Why choose welded titanium tubing instead of seamless?

A: Welded tubing offers tighter wall tolerances, longer continuous lengths and lower cost per metre, while achieving corrosion performance comparable to seamless tube when properly welded and annealed.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry