Aug 07, 2025 Leave a message

Technical Specifications for Surface Pickling of Titanium Alloy Castings

I. Technical Requirements for Process Equipment

1. Pickling Tank System

(1) Tank Structure

Main Material: 304 Stainless Steel Welded Base

Lining Material: 8mm Thick Rigid Polyvinyl Chloride (PVC) Plastic Board

Alternative: Integral PVC Plastic Tank (Applicable when Volume < 2m³)

(2) Temperature Control System

Cooling Device: Coil-type Titanium Alloy Heat Exchanger

Temperature Monitoring: Digital Display Temperature Sensor (Accuracy ±1°C)

Working Temperature Range: 20-50°C Adjustable

(3) Waste Gas Treatment

Sealing System: Pneumatic Lifting PVC Cover

Exhaust System: PP Centrifugal Fan (Air Volume ≥ 2000m³/h)

Purification Device: Three-stage Alkaline Solution Spray Tower

2. Auxiliary equipment
(1) Tooling system
Hanger material: TA2 pure titanium/316L stainless steel (PTFE coating required)
Load structure: Modular combination design (maximum load 500kg)
Protection requirements: Contact parts need to be covered with silicone protective covers
(2) Drying system
Hot air circulation drying oven
Temperature control range: 50-105℃ adjustable
Wind speed adjustment: 0.5-3m/s stepless speed change
II. Standardized process flow
1. Pretreatment stage
(1) Sandblasting
Abrasive selection: 80-120 mesh white corundum
Jet pressure: 0.4-0.6MPa
Surface roughness control: Ra3.2-6.3μm
(2) Degreasing and cleaning
Solvent selection: Aviation grade 120# gasoline → industrial anhydrous ethanol secondary cleaning
Cleaning method: Ultrasonic cleaning (frequency 40kHz, temperature 50℃)
Time control: 10±2 minutes/tank

1 21
1 20
1 19
1 12

2. Main pickling process
(1) Pickling pre-treatment
Three-stage countercurrent rinsing: normal temperature tap water → deionized water → RO pure water
Water film continuity test: >30 seconds is qualified
(2) Pickling operation
Tannel circulation: magnetic pump forced circulation (flow rate 1.5m/s)
Workpiece spacing: ≥50mm
Process monitoring: pH value and metal ion concentration are tested every 15 minutes
(3) Post-treatment
Neutralization treatment: 5% NaHCO3 solution immersion (2-3 minutes)
Pure water spray: conductivity <10μS/cm
Hot air drying: 80℃×20min (humidity ≤30%RH)
III. Pickling solution formula system
1. The solution needs to be replenished with fresh acid every shift, and the HNO3:HF addition ratio is controlled at 20:1
2. Metal ion concentration exceeds the standard (tank solution needs to be replaced when Ti³+>15g/L)
3. An online density meter automatically monitors the specific gravity of the solution (range: 1.15-1.25 g/cm³).
IV. Key Quality Control Points
1. Surface Cleanliness: ASTM B600 standard testing, Grade 2 or higher
2. Hydrogen Embrittlement Control: Hydrogen content ≤ 150 ppm (determined by thermal conductivity method)
3. Dimensional Accuracy: Corrosion in key areas ≤ 0.05 mm
4. Surface Color: Uniform silver-white, no excessive corrosion spots
V. Safety Precautions
1. Operators must wear:
Fully enclosed acid-resistant mask
Butyl rubber gloves (thickness ≥ 0.5 mm)
PVC chemical protective clothing
2. Emergency Response:
Eyewash station installation distance ≤ 10 m
Neutralizer storage (lime milk + boric acid solution)
3. Environmental Monitoring:
HF concentration in the work area ≤ 1 mg/m³ (real-time monitoring and alarm)
Wastewater pH adjusted to 6-9 before discharge
This technical specification refers to GB/T 25151-2010 "Technical Specification for Pickling of Chemical Equipment" and AMS 2488D Titanium Alloy Surface Treatment Standard were formulated, which are applicable to the surface treatment of high-end titanium castings such as aerospace and medical implants.

about Us

The company boasts leading domestic titanium processing production lines, including:

German-imported precision titanium tube production line (annual production capacity: 30,000 tons);

Japanese-technology titanium foil rolling line (thinnest to 6μm);

Fully automated titanium rod continuous extrusion line;

Intelligent titanium plate and strip finishing mill;

The MES system enables digital control and management of the entire production process, achieving product dimensional accuracy of ±0.01μm.

4242

 

Send Inquiry

whatsapp

Phone

E-mail

Inquiry