Oct 13, 2025 Leave a message

Titanium Gr 1 Polished Pipes and Tubes for Chemical Processing

Why Grade 1 Titanium for Chemical Processing Piping

Titanium Grade 1 (UNS R50250) is the softest and most formable of the commercially pure grades. High ductility, excellent cold formability and a stable passive oxide film make it the default choice for polished tubing in chemical, chlor-alkali and water treatment service, and for pharmaceutical lines where a smooth, chemically clean bore is required. Grade 1 tubing is selected where bends, coils and expansion loops must be formed without cracking, and where the process stream is oxidising or neutral rather than a hot reducing acid.

Against austenitic stainless steel, Grade 1 titanium is roughly 45% lighter for the same wall, tolerates chloride-bearing streams that would stress-crack stainless steel, and resists fouling because its passive surface stays chemically inert in most process fluids.

Material Specification and Mechanical Properties

Titanium Gr 1 pipes and tubes are normally ordered to ASTM B338 and ASME SB338 for seamless and welded tube used in condensers and heat exchangers, ASTM B861 and ASME SB861 for seamless pipe, ASTM B862 and ASME SB862 for welded pipe, and ASTM B337 for welded tube. National-standard equivalents are covered by GB/T 3624 and GB/T 3625, and Japanese practice by JIS H 4630. Purchase orders state the grade, the UNS number, the manufacturing route, the heat treatment condition and the test schedule.

Property Grade 1 value
UNS number R50250
Chemistry limits Fe 0.20 max, O 0.18 max, C 0.08 max, N 0.03 max, H 0.015 max, Ti balance
Density 4.51 g/cm3
Melting point Approximately 1668 °C
Tensile strength 240 MPa minimum
0.2% yield strength 138 MPa minimum
Elongation 24% minimum
Modulus of elasticity Approximately 103 GPa
Thermal conductivity Approximately 16-17 W/m·K at room temperature

The low yield strength is a design input rather than a defect. It is the reason Grade 1 accepts tight U-bends, rolled joints and cold flaring without cracking, and the reason it is not used for high-pressure lines where Grade 2 or Grade 5 carries the load.

Size Range and Delivery Condition

Pipe: 15 NB up to 600 NB in schedules 5S, 10S, 40S, 80S and heavier walls.

Tube: outside diameter 6-254 mm with wall thickness 0.5-20 mm; capillary sizes from 3 mm outside diameter on request.

Lengths: single random, double random or cut to a fixed length up to 15 m for pipe.

Ends: plain, bevelled or threaded; U-bend and coil forms for heat exchanger bundles.

Delivery condition: annealed, bright annealed, pickled or polished, seamless or welded, with 100% eddy current or hydrostatic testing.

Section shapes: round as standard, with square, oval and spiral forms available for special assemblies.

Surface Finishes: Pickling, Polishing and Electropolishing

Chemical processors specify finish because roughness drives both corrosion initiation and product contamination. Pickling in a nitric-hydrofluoric bath, typically 30-50 vol% nitric acid with 1-3 vol% hydrofluoric acid at 20-40 °C, removes the mill oxide and restores the passive layer, leaving a uniform matte surface. Mechanical polishing with progressively finer abrasives produces a bright finish with a controlled scratch pattern. Electropolishing in a phosphoric-sulfuric electrolyte removes the outer metal layer, rounds micro-peaks and leaves a chemically clean surface that is easier to clean in place and dries without residue.

Finish Typical surface roughness Typical application
Pickled Ra 0.8-1.6 µm General chemical pipework, large bore lines
Mechanically polished Ra 0.4-0.8 µm Heat exchanger tubes, hygienic transfer lines
Electropolished Ra 0.2-0.4 µm Fine chemical, pharmaceutical and high purity service

Polished tubing is handled with soft slings and plastic end caps. A polished surface that has been scratched or touched with bare carbon steel hands no longer performs as specified, because embedded iron becomes the weakest point in the passive film.

Corrosion Behaviour and Service Limits

Grade 1 resists nitric acid across a wide concentration range, chlorides, hypochlorites, sea water and most neutral salt solutions, and it is immune to the chloride stress corrosion cracking that attacks austenitic stainless steels. The passive film needs oxygen or another oxidising species to repair itself, so performance falls in hot, deaerated reducing acids. Hydrochloric and sulfuric acid duty is normally handled by a palladium-bearing or molybdenum-bearing grade rather than Grade 1.

Three limits deserve attention at the design stage: crevice corrosion under gaskets, supports and deposits in hot chloride brines above about 70 °C; hydrogen pickup in strongly cathodic or reducing conditions; and fluoride ions plus wet chlorine, which attack the passive film directly. Dry chlorine is handled, wet chlorine is not.

Quality Control and Documentation

Heat analysis and product analysis per heat, with mill certificates issued to EN 10204 3.1.

Hydrostatic or pneumatic pressure test, plus 100% eddy current or ultrasonic testing of the tube body.

Dimensional checks on outside diameter, wall thickness and ovality, with wall thickness recording on request.

Flattening, flaring and reverse bend tests for welded tube, and a tensile test per heat.

Surface verification at the agreed roughness, with no embedded iron and no residual polishing compound.

Clean packing with end caps, waterproof paper and non-reactive crating to protect the polished bore in transit.

Frequently Asked Questions

Q: When should Grade 1 be chosen instead of Grade 2?
Choose Grade 1 when the limiting requirement is formability or a mirror finish, such as U-bend heat exchanger tubes, coils and hygienic lines. Where pressure, erosion or vibration governs the design, Grade 2 carries the load better.

Q: What standards cover Grade 1 titanium pipe and tube?
ASTM B861 and ASME SB861 for seamless pipe, ASTM B862 and ASME SB862 for welded pipe, and ASTM B338 together with ASME SB338 for seamless and welded heat exchanger tube, with GB/T 3624 and GB/T 3625 as national-standard equivalents.

Q: Is pickling or electropolishing needed after polishing?
They are alternatives, not a sequence. Pickling restores the passive layer and removes mill oxide; electropolishing removes the outermost metal layer and rounds micro-peaks. Where the specification calls for a bright polished finish, pickling is usually the pre-treatment step before mechanical polishing.

Q: How does titanium compare with stainless steel for chloride service?
Grade 1 tolerates chloride streams that cause stress corrosion cracking in austenitic stainless steels, and its passive film is stable in sea water. The exception is hot concentrated chloride in crevices, where a higher alloy titanium grade is the safer choice.

Q: Can Grade 1 tube be bent and coiled in the polished condition?
Yes, provided the bend radius stays above the minimum set for the wall thickness and tooling is clean and hardened. Bends below that radius are stress relieved or made from annealed stock to avoid surface rumpling.

Q: What evidence of corrosion resistance is supplied with the order?
Mill certificates carrying heat number, chemistry and mechanical results, dimensional records, test reports for pressure and non-destructive examination, and a certificate of compliance with the ordered standard.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry