Sep 08, 2025 Leave a message

Titanium Tube Annealing Process: Temperature, Atmosphere and Cooling Control

Titanium tube annealing is the controlled heat treatment that decides whether a finished heat exchanger, condenser or desalination tube performs reliably for decades. The operation looks simple – heat, hold, cool – but the window between a fully recrystallised, stress-free structure and a contaminated or over-grown one is narrow. For seamless and welded tube supplied to ASTM B338 / ASME SB338, ASTM B337 / ASME SB337, ASTM B861 and ASTM B862, the annealing cycle is a specified manufacturing parameter, not an optional finishing step.

Why Annealing Titanium Tube Matters

Cold pilgering, plug drawing, straightening and welding all leave residual stress and a deformed grain structure in the tube wall. Left in place, that condition shows up downstream as dimensional movement during machining, reduced fatigue life in cyclic service, and a greater tendency to stress corrosion cracking in chloride-bearing waters.

Stress relief – relaxes residual stress from cold reduction and fabrication, stabilises dimensions and improves resistance to stress corrosion cracking.

Recrystallisation – replaces the elongated, work-hardened structure with uniform equiaxed grains, restoring ductility and toughness.

Property restoration – brings Grade 1, Grade 2, Grade 7, Grade 9 and Grade 12 tube back to the tensile strength, yield strength, elongation and hardness values ordered by the customer.

Cleanliness – bright annealing in vacuum or high-purity argon suppresses the oxide scale that would otherwise have to be removed by acid pickling.

Annealing Cycles and Typical Parameters

Four cycles cover almost all commercial tube. The values below are typical shop-floor ranges for commercially pure and alpha-beta grades; the released schedule always follows the qualified procedure and the purchase specification.

Cycle Typical temperature Hold time Cooling Primary purpose
Stress relief 480 – 650 °C 30 – 120 min Furnace or controlled Relax fabrication stress, hold dimensions
Recrystallisation (mill anneal) 650 – 760 °C 30 – 90 min Air or argon Restore a fully equiaxed structure
Bright anneal (vacuum or argon) 700 – 800 °C 20 – 60 min Controlled to below 200 °C Scale-free surface with restored ductility
Beta anneal (Ti-6Al-4V tube) Above the beta transus, about 1,000 – 1,050 °C 10 – 30 min Air or controlled Toughness and creep performance in high-strength grades

Two rules govern the schedule. First, hold time starts only when the whole load, not the furnace thermocouple, has reached temperature. Second, soaking an alpha-beta alloy above the beta transus grows the beta grain size quickly and irreversibly, so the soak is kept as short as the specification allows.

Furnace Atmosphere and Contamination Control

Titanium absorbs oxygen, nitrogen, hydrogen and carbon above roughly 600 °C, and once a contaminated layer has formed it cannot be removed by reheating. Atmosphere control therefore carries more weight than any other single variable.

Use vacuum with an ultimate pressure in the 10-2 to 10-3 Pa range, or argon at 99.999 % purity.

Hold the dew point of the argon supply at -40 °C or below and monitor it continuously through the soak.

Keep a small positive pressure inside the retort so that air cannot be drawn in through seals and flanges.

Deliver the load free of oil, fingerprints, machining coolant and marking ink; alkaline cleaning followed by a demineralised water rinse is standard practice.

Prevent the tube from touching carbon steel fixtures at temperature; dedicated titanium or ceramic supports stop iron contamination.

A straw-yellow or light-blue tint after annealing indicates a thin oxide layer that ordinary pickling will remove. A dull grey, chalky white or purple-brown surface points to a hard, oxygen-enriched alpha case, and the affected tube should be sectioned for hardness and metallographic evaluation before it is accepted.

Step-by-Step Process Sequence

Incoming inspection – confirm grade, dimensions, straightness and surface condition against ASTM B338 / ASME SB338 or the ordered tube specification.

Degreasing and cleaning – remove oil, oxide, drawing lubricant and handling marks before loading.

Loading – rack the tube so the load is evenly spaced and free to expand, and record the charge number against the heat number.

Evacuation or purging – reach the target vacuum, or displace the air in the retort with argon, before heating begins.

Heating – ramp at a controlled rate, typically 100 – 200 °C per hour for thin-wall tube, to limit thermal gradients.

Soak – hold at the qualified temperature for the specified time once the load is uniformly at temperature.

Cooling – apply the specified cooling mode and never break vacuum or open the retort above 200 °C.

Post-treatment – pickle or mechanically clean where required, then check dimensions, straightness and surface finish.

Testing and certification – tensile, flattening, flare, hardness and hydrostatic tests as ordered, released with a mill test certificate to EN 10204 3.1.

Acceptance Testing and Typical Composition Limits

Annealing does not change chemistry, but contamination is detected by chemistry. Typical maximum limits for Grade 2 seamless tube under ASTM B338 are listed below. Every heat is verified by certified chemical analysis and, where the order requires it, by hardness or metallographic examination.

Element Typical maximum, Grade 2 tube Effect of excess
Oxygen 0.25 % Raises strength, lowers ductility, forms alpha case
Nitrogen 0.03 % Strong hardening with a sharp loss of toughness
Hydrogen 0.015 % Hydrogen embrittlement and delayed cracking
Carbon 0.10 % Carbide formation, reduced corrosion resistance
Iron 0.30 % Beta stabilisation, altered transformation behaviour

Hardness is the fastest shop-floor indicator. A rise of more than about 10 HV above the annealed reference for the same grade justifies metallographic examination for alpha case, especially on tube destined for heat exchangers or condensers.

Frequently Asked Questions

Q: What is the difference between stress relief annealing and full recrystallisation annealing?
Stress relief keeps the worked grain structure and only relaxes residual stress, so it runs in the lower temperature range. Full recrystallisation annealing replaces the deformed structure with new equiaxed grains and restores ductility, which needs the higher temperature range and a longer soak.

Q: Can titanium tube be annealed in air?
Only for intermediate or non-critical operations. A final anneal in air produces an oxide layer and an oxygen-enriched subsurface that must be removed by pickling, which changes wall thickness and surface finish. Vacuum or high-purity argon is the normal route for finished tube.

Q: Why does titanium tube turn blue after annealing?
Interference tinting shows the thickness of the oxide layer. Silver or light straw is normal; blue, purple or grey means air or moisture entered the retort, the argon purity was low, or the load was exposed above 200 °C. Pickle the affected length and correct the atmosphere before the next charge.

Q: How long should titanium tube be soaked at the annealing temperature?
For recrystallisation, 30 to 90 minutes at temperature is typical once the load is uniformly hot, with shorter times for thin-wall bright annealing and longer times for heavy wall or dense bundles. The released procedure, supported by hardness and metallographic results, fixes the final value.

Q: Does annealing lower the strength of Grade 5 titanium tube?
It can. Annealed Ti-6Al-4V is supplied in a softer condition than solution treated and aged material, so the specified condition must match the design requirement. Where higher strength is needed, the heat treatment schedule and the resulting mechanical properties are agreed with the customer before production.

Q: Is vacuum annealing always better than argon annealing?
Vacuum gives the cleanest surface and helps to remove hydrogen, but it costs more per charge and is limited by pump capacity and load outgassing. High-purity argon with a controlled dew point is perfectly adequate for many grades. Either way, leak rate, dew point and load cleanliness decide the result.

Q: Which tube standards does annealing support?
Finished tube is normally certified to ASTM B338 / ASME SB338, ASTM B337 / ASME SB337, ASTM B861, ASTM B862 or ASTM B863 depending on product form, with dimensional and mechanical testing defined by the ordered specification.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry