Oct 15, 2025 Leave a message

ASTM-B338.pdf

ASTM B338 Grade 4 Titanium Cold-Rolled Tube

Grade 4 Titanium and Its Role

Grade 4 titanium, UNS R50700, is the strongest member of the commercially pure family, with a minimum tensile strength of 550 MPa, minimum yield strength of 480 MPa and elongation of at least 15 percent in a 50 mm gauge length. The strengthening comes mainly from oxygen, controlled up to about 0.40 percent, which raises strength without the alloying additions that complicate welding and forming.

ASTM B338 covers seamless and welded titanium tube for condensers and heat exchangers, and Grade 4 is approved in both forms. The grade is used where the design needs more strength than Grade 2 but where the corrosion resistance of pure titanium is still required, or where alloyed grades such as Grade 5 would be unnecessarily expensive and difficult to form.

What Cold Rolling Does to the Tube

Cold rolling, performed on a pilger or cold rolling mill, reduces the tube diameter and wall without heating, using successive passes of shaped rolls over a mandrel. The process refines the grain structure, improves dimensional accuracy and produces a smooth, bright surface. Between passes the tube is annealed to restore ductility, and the final pass sets the finished dimensions and tolerances.

Compared with hot-finished tube, cold-rolled tube holds wall thickness and outside diameter to tighter tolerances, shows better surface finish, and has more consistent mechanical properties along the length. These characteristics are exactly what exchanger fabrication needs: uniform tube for rolling into tube sheets, predictable bend behaviour and reliable pressure integrity.

Properties After Cold Rolling

The cold-rolled and annealed tube shows the full Grade 4 strength with adequate ductility for the forming operations of bundle fabrication. The higher strength permits a thinner wall for the same design pressure, which improves heat transfer and reduces the weight of the bundle. The oxide film that provides corrosion resistance forms naturally on the clean surface and is unaffected by the cold work.

Wear and erosion resistance are higher than the softer grades because of the greater hardness, which helps in services with suspended solids and high flow velocities. Fatigue behaviour is also good, and the fine-grained structure from controlled rolling and annealing gives consistent performance from tube to tube within a lot.

Applications of Grade 4 Cold-Rolled Tube

Grade 4 tube is specified for high-pressure heat exchangers, surface condensers, seawater coolers and geothermal service, where the pressure rating or erosion resistance demands a stronger pure titanium tube. It is also used for chemical process exchangers handling hot chlorides and for marine systems where wall thickness must be minimised to fit the bundle envelope.

In retrofit projects, replacing a Grade 2 bundle with Grade 4 can raise the exchanger's allowable working pressure without changing the shell, because the thinner wall and higher allowable stress change the tube-side capacity. The upgrade is straightforward because the tube dimensions and bundle geometry can be kept identical.

Quality Control and Certification

Each lot of cold-rolled Grade 4 tube is examined full length by eddy current or ultrasonic testing, and samples are tensile tested, flattened and flared to confirm the forming behaviour. Dimensional checks verify diameter, wall, straightness and end squareness, and hydrostatic testing is applied where the design requires it. The material test certificate documents chemistry, mechanical properties and the heat treatment condition.

The certification allows the exchanger fabricator to trace every tube to its melt and to verify that the lot meets the design specification. This disciplined quality chain, combined with the inherent corrosion resistance of titanium, is the reason Grade 4 cold-rolled tube serves reliably in the most demanding pure-titanium duties.

Frequently Asked Questions

Q: What is the strength of cold-rolled Grade 4 titanium tube?

A: Grade 4 has a minimum tensile strength of 550 MPa and yield strength of 480 MPa, the highest of the commercially pure titanium grades.

Q: How does cold rolling improve titanium tube?

A: Cold rolling tightens dimensional tolerances, refines the grain structure and gives a smooth bright surface, improving both fabrication and service behaviour.

Q: Is Grade 4 tube stronger than Grade 2?

A: Yes, about 60 percent stronger in tensile strength, which allows thinner walls and higher pressure ratings for the same corrosion resistance.

Q: Can cold-rolled Grade 4 tube be U-bent and rolled into tube sheets?

A: Yes, the annealed condition retains enough ductility, and bundle fabrication follows the controlled practice used for other titanium grades.

Q: Where is Grade 4 cold-rolled tube mainly used?

A: In high-pressure heat exchangers, condensers, seawater coolers and geothermal service where the pressure rating or erosion resistance demands higher strength pure titanium.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry