Grade 4 Titanium in Exchanger Circuits
Heat exchanger systems need not only tubes but also the connecting piping that carries process and service fluids. Grade 4 titanium, UNS R50700, offers the highest strength of the pure titanium grades, with minimum tensile strength of 550 MPa, yield strength of 480 MPa and elongation of at least 15 percent. ASTM B338 covers its tubular products for condenser and heat exchanger service, including the round pipe of the exchanger circuit.
The grade is selected where the exchanger operates at higher pressure or where erosion from suspended solids demands a harder surface. Because it remains a pure titanium chemistry, the corrosion resistance in seawater, chlorides and oxidising acids is the same as the softer grades.
The Value of a Polished Surface
Polishing removes surface roughness and scale, leaving a smooth finish that resists fouling. In exchanger piping, fouling layers act as insulation and reduce heat transfer, so a smooth bore keeps the circuit performing at design duty longer. Polished surfaces also clean more easily, whether by flushing, pigging or chemical cleaning, reducing downtime.
The finish is achieved by grinding and buffing the tube or pipe surface, followed by pickling or passivation to restore the protective oxide film. The result is a bright, uniform surface that also makes inspection easier: surface defects are visible, and the absence of scale removes the sites where corrosion can start under deposits.
Mechanical and Corrosion Properties
The high strength of Grade 4 allows thinner walls for the same pressure, reducing weight and improving the heat transfer of the circuit. The hardness of the material, higher than Grade 2, resists erosion in high-velocity flow and in services with abrasive particles. Fatigue resistance is good, and the fine-grained annealed structure gives consistent behaviour along the line.
Corrosion resistance matches the other pure grades: immunity to chloride pitting and stress corrosion, and good resistance to oxidising acids and seawater. The polished surface enhances this by preventing the initiation of attack under scale and deposits, which is the classic starting point of crevice corrosion in less noble materials.
Applications in Heat Exchanger Systems
Polished Grade 4 pipe is used for exchanger inlet and outlet piping, seawater headers, high-pressure condensate lines and the small-bore connections of instruments in severe services. It is also used for exchanger tubes where the combination of pressure, erosion and fouling control justifies the grade and finish.
In power plants and chemical plants with chloride-laden cooling water, the polished surface and high strength extend the intervals between cleaning and inspection, improving availability. The pipe installs with standard titanium practice: argon-shielded welding, clean handling and controlled bending, with the same fabrication rules as other titanium grades.
Fabrication and Quality Control
Polished pipe is cut, welded and installed with the clean-handling discipline that titanium requires, and the polished bore is protected during fabrication by end caps and clean work areas. Welds are made under argon with matching filler, and the weld area is brushed and pickled to restore the surface condition. The completed circuit is pressure tested and examined according to the code requirements.
Quality control at the mill includes full-length non-destructive examination, tensile and forming tests, and dimensional verification. Each lot is certified with chemistry and mechanical results, and the polished condition is confirmed by surface roughness measurement where the specification calls for it.
Frequently Asked Questions
Q: Why is polished titanium pipe used in heat exchangers?
A: The smooth surface resists fouling, keeps heat transfer high, simplifies cleaning and prevents corrosion initiation under deposits.
Q: What is the strength of Grade 4 titanium pipe?
A: Minimum tensile strength is 550 MPa and yield strength is 480 MPa, the highest of the commercially pure titanium grades.
Q: Does polishing affect the corrosion resistance of titanium?
A: No, after polishing the surface is pickled or passivated to restore the protective oxide film, and the clean surface actually improves corrosion behaviour.
Q: Can polished Grade 4 pipe be welded in the field?
A: Yes, with argon-shielded gas tungsten arc welding, followed by brushing and pickling of the weld area to restore the surface condition.
Q: Where is Grade 4 polished pipe mainly applied?
A: In exchanger circuits with high pressure, high velocity or abrasive flow, and in seawater and chloride services where fouling control matters.





