Titanium and its alloys are among the most difficult metals to cast, yet cast titanium components are indispensable in aerospace, marine, chemical processing and medical devices. The difficulty comes from titanium's extreme reactivity with oxygen, nitrogen and most mold materials at elevated temperatures. This article explains how titanium castings are actually produced, which mold systems and melting technologies are used, and how quality is verified against ASTM B367.
Why Titanium Casting Is Different
Molten titanium reacts aggressively with air and with conventional refractory mold materials. Three consequences follow:
Melting must be carried out in vacuum or inert atmosphere. Open-air melting would absorb oxygen and nitrogen, embrittling the casting.
Mold materials must be refractory and chemically stable. Reactive mold constituents would be reduced by the titanium, contaminating the surface with an oxygen-enriched alpha case.
Post-casting surface removal is mandatory. The oxygen-rich surface layer (alpha case) must be removed by machining or chemical milling because it is hard and brittle.
Melting Technologies
Two melting routes dominate commercial titanium casting:
Vacuum Arc Remelting (VAR): A consumable electrode is melted under vacuum into a water-cooled copper crucible. VAR provides a clean, homogeneous melt and is the most widely used industrial route.
Cold Hearth Melting (CHM) with electron beam or plasma: The melt is held in a water-cooled copper hearth, which removes high-density inclusions (such as tungsten from scrap) and low-density inclusions (such as nitrides). CHM is preferred for rotating aerospace components.
Mold Systems
Investment (lost-wax) casting is the most common process for titanium. A wax pattern is coated with multiple ceramic slurries, the wax is removed by autoclaving, and the mold is fired. For titanium, the face coat is usually based on zirconia or yttria rather than silica, because silica is reduced by molten titanium. Investment casting delivers excellent dimensional accuracy (typically CT6–CT7 per ISO 8062) and smooth surfaces, and is used for complex parts such as impellers, brackets and prosthetic implants.
Rammed graphite molding is a lower-cost route for larger or simpler shapes. The mold is made by ramming graphite-based refractory around a pattern, then firing. Thermal shock resistance is good, and large marine or chemical components are often produced this way, with a trade-off in surface finish and dimensional tolerance (typically CT8–CT10).
Centrifugal casting spins the mold while the metal solidifies, improving filling of thin sections and directional density. It is used for rings, sleeves and other axisymmetric parts in corrosion-resistant alloys.
Common Casting Alloys
| Alloy | Typical Use | Characteristics |
|---|---|---|
| Commercially pure Ti (Gr 1–4) | Chemical vessels, marine hardware | Best corrosion resistance; moderate strength |
| Ti-6Al-4V (Gr 5) | Aerospace brackets, surgical implants | High strength, good fatigue performance |
| Ti-6Al-4V ELI (Gr 23) | Cryogenic and implant applications | Improved low-temperature toughness |
| Ti-6Al-2Sn-4Zr-2Mo | Engine components | High-temperature creep resistance |
Castability, weldability and heat-treatment response differ between alpha, alpha-beta and near-beta alloys; alloy selection should be confirmed against the component's service temperature, load spectrum and corrosion environment.
Quality Control
Castings are typically supplied to ASTM B367 (titanium and titanium alloy castings) with supplementary radiographic, dye-penetrant and mechanical testing. Key checks include:
Chemical composition verification by spectrochemical analysis.
Radiographic examination (ASTM E155 reference radiographs) for shrinkage, porosity and inclusions.
Dye penetrant inspection for surface discontinuities.
Mechanical testing of separately cast test bars after the same heat treatment as the casting.
Alpha-case depth control and removal verification.
Hot Isostatic Pressing (HIP) is commonly specified for critical aerospace and medical castings to close internal porosity and improve fatigue life.
Cost and Selection Guidance
Investment casting offers the best accuracy and finish but the highest tooling cost. Rammed graphite molding suits larger, simpler parts and lower volumes. For prototype work, additive manufacturing of the pattern followed by investment casting reduces lead time. When selecting a foundry, verify its melting capability (VAR or CHM), its experience with the target alloy, and its compliance with the inspection level required by your application.





