How Titanium Tubing Entered Industrial Service
Corrosion resistant titanium tubing has been used in the process industries for about a quarter of a century and is now standard equipment in chemical plants, petrochemical units, salt manufacturing, non-ferrous metallurgy and desalination. Titanium resists chlorides, oxidising acids and seawater, so it replaced stainless steel and nickel based materials in heat exchangers, condensers and transfer lines where wet corrosion was the limiting factor. Its spread was slower than the metal itself deserved, because pipelines also depend on fittings, and the early weak point of a titanium line was not the tube but the joints that connected it.
The Origins of Standardised Pipe Dimensions
Metal pipes have been manufactured for more than 200 years, but the serialisation of pipe sizes only began in the 1920s, when industry needed a repeatable way to match tubes, fittings and flanges. The inch integer of the internal diameter was adopted as the nominal diameter, or DN, and the sizes were arranged into a series. National practices then diverged: the outside diameter provisions used in the United Kingdom, the United States and Japan were essentially the same and formed a large diameter series, while Germany and Italy based their systems on smaller outside diameters and produced a separate, smaller series.
Only about seventy years ago were internationally comparable specifications issued for these series, with the millimetre adopted as the length unit. During the 1980s many countries published complete technical standards for pipelines, and that wave of work finally unified the reference dimension used for ordering piping components.
Development of Pipeline and Fitting Standards
Standardisation of oil and process pipe components began later than that of the tubes themselves. Early fitting standards were issued by the petroleum and chemical industry authorities in the early 1980s, covering seamless bends and the joining of carbon steel and low alloy steel line pipe. These were followed by wider national specifications for steel butt welding seamless pipe fittings, which remain the reference document for fitting dimensions today and are supported by international fitting standards such as the ASME B16.9 series.
The Seamless Fitting Breakthrough
Welded fittings were originally used for bends and crossings in titanium lines. These fabricated joints were difficult to construct, had a comparatively short service life, and became the weakest element that limited the life of an entire pipeline. After several years of development work, a non-ferrous metals research institute succeeded in producing seamless titanium fittings by a special extrusion method, including elbows, reducers, tees and lap joint flange fittings. The development closed the gap in titanium piping systems and brought construction and installation of titanium pipelines up to the standard of the tube itself, and the service life of the pipelines more than doubled as a result.
Titanium fitting standards were then drafted to match the national fitting standard, covering elbows, tees, reducers and loose flange fittings, with specifications, materials and inspection requirements aligned with the titanium tube standards so that a complete system could be ordered from a single dimensional basis.
Nominal Diameter Series and the A/B Division
The serialisation of fittings is based on nominal diameter and is divided into about nineteen size steps expressed in inches or millimetres. Nominal diameter is an integer series that is similar to, but not equal to, the internal diameter of the pipe. Every dimension of the connection can be derived from the nominal diameter and the pipe type, with wall thickness as the main variable.
Outside diameter is the most important practical sizing parameter, because it governs the fit between tube, fitting and flange.
A series follows the large diameter, internationally aligned provisions and is preferred for new equipment to achieve uniformity.
B series follows the older domestic provisions and continues to be used for replacement work in existing plants.
The A and B systems are expected to coexist for a long time, so drawings and purchase orders must state the series explicitly.
Modern Titanium Tube Standards
| Standard | Scope |
|---|---|
| ASTM B338 | Seamless and welded titanium and titanium alloy tubes for condensers and heat exchangers |
| ASTM B861 | Seamless titanium and titanium alloy pipe for general service |
| ASTM B862 | Welded titanium and titanium alloy pipe for general service |
| ASTM B363 | Seamless and welded titanium fittings for general service |
| ASTM B381 | Titanium and titanium alloy forgings used for flanges and valve bodies |
| ASME B16.9 | Butt welding fittings, used as the dimensional reference for fitting geometry |
Grades are selected to match the service medium: unalloyed grades for oxidising and neutral environments, palladium bearing grades for reducing acids, and alloy grades where higher strength is needed. Because titanium piping is usually thin walled and welded in place, shielding gas protection, joint preparation and cleanliness during installation remain the decisive factors in service life.
Lessons for Today's Specifications
The history of titanium tubing shows that a corrosion resistant alloy only delivers its full life when the whole system, not just the tube, is engineered to the same standard. Specifying a tube grade without stating the dimensional series, the fitting standard and the joint type leaves the weakest link undefined. Modern purchase specifications therefore state the tube standard, the fitting standard, the nominal diameter series, the grade and the inspection requirements together, and require dimensional and material traceability for fittings as well as for tubes.
Frequently Asked Questions
Q: How long has titanium tubing been used in industry?
Corrosion resistant titanium tubing has been in civil industrial service for about a quarter of a century, mainly in chemical, petrochemical, salt manufacturing and non-ferrous metallurgy plants where chloride and oxidising media shorten the life of stainless steel.
Q: What is the nominal diameter series and why does it matter?
Nominal diameter is an integer size series based on the inch diameter of the pipe interior, arranged in approximately nineteen steps. It allows tubes, fittings and flanges to be matched by size, and it is the reason a purchase order must state the series together with the outside diameter.
Q: What is the difference between the A series and the B series?
The A series follows the large diameter provisions that are aligned internationally and is preferred for new equipment to keep systems uniform. The B series follows older domestic provisions and remains in use for replacement work in existing plants, so the two series continue to coexist.
Q: Why did welded titanium fittings limit pipeline life?
Fabricated welded bends and crossings were difficult to construct and had a shorter service life than the tube, so the joints became the weakest part of the installation. Seamless fittings produced by extrusion removed that limitation and more than doubled the service life of complete pipelines.
Q: Which standards cover modern titanium tube and fittings?
Titanium tubes for heat exchangers and condensers are specified to ASTM B338, general service pipe to ASTM B861 and ASTM B862, fittings to ASTM B363, and forgings to ASTM B381, with ASME B16.9 used as the dimensional reference for butt welding fittings.
Q: What should a titanium piping specification include?
The tube standard and grade, the fitting standard, the nominal diameter series, wall thickness, the welding and inspection requirements, and material traceability for both tubes and fittings. Stating the grade alone leaves the dimensional and joint requirements undefined.





