Dec 05, 2023 Leave a message

How to Select Titanium Beneficiation and Process Equipment

Two Meanings of Titanium Equipment Selection

The phrase titanium equipment selection covers two distinct buying decisions that are often confused. The first is the mineral processing equipment used to upgrade titanium bearing ores into a saleable concentrate, where the machines are usually conventional in construction and the selection problem is metallurgical. The second is process equipment fabricated from titanium, such as heat exchangers, columns, tanks and piping in chlorides or oxidising media, where the selection problem is material and fabrication quality. A sound selection exercise separates the two and answers the metallurgical question first, because the ore body determines the flowsheet, and the flowsheet determines the size, the wear duty and the number of units.

Start From the Ore Body, Not From the Equipment List

Titanium is dispersed in nature and rarely occurs in a form that can be shipped directly, which is why selection work begins with mineralogy. Ilmenite, with the formula FeTiO3, carries a theoretical maximum of about 52.7 percent titanium dioxide, but commercial concentrates usually report lower values because of weathering, exsolution and intergrowths. Rutile offers a much higher grade but is far less abundant. The real questions for equipment selection are the mineral assemblage, the proportion of coexisting minerals and gangue, and above all the liberation size, that is the particle size at which the iron bearing and titanium bearing grains can be separated as single crystals.

Two ore bodies with the same head grade can require completely different equipment if their liberation sizes differ by a factor of three. Fine intergrowths push the flowsheet towards fine grinding followed by flotation, while coarse, well liberated material can often be treated with screening, gravity concentration and dry separation alone. Grinding finer than the liberation size wastes energy and creates slimes that ruin downstream recovery, so a locked cycle test at pilot scale is the cheapest insurance before committing to a flowsheet.

Choosing the Separation Route

Titanium minerals respond to several physical properties, and most concentrators combine at least two of them.

Gravity separation exploits the density difference between ilmenite and silicate gangue, and is normally applied to the coarse fraction in spirals, cones or shaking tables.

High intensity magnetic separation takes advantage of the paramagnetic character of ilmenite. It is the workhorse step for both roughing and cleaning, and it also allows recovery of iron minerals from tailings.

Electrostatic separation works on differences in conductivity and is applied to dry, closely sized feed, typically the coarse fraction after screening and classification.

Flotation is applied to the fines, where gravity and dry separation lose efficiency. Anionic collectors are the standard chemistry; modified tar oil based collectors are widely available, capture ilmenite strongly and can be prepared in advance for room temperature flotation, which makes them an effective and practical collector.

Combined flows such as gravity, strong magnetic, flotation and electric separation in series are used to recover titanium and iron values from old tailings, where the mineralogy is more complex.

A reported industrial trial of a screening and classification circuit followed by coarse particle electric separation and fine particle flotation achieved a titanium concentrate grade of 47.65 percent with a recovery of 78.34 percent in the cleaning stage. Those are operation specific figures, but they illustrate the usual trade off: pushing grade up by heavier cleaning tends to reduce recovery, so the economic optimum must be evaluated against the smelter or pigment plant specification rather than against the highest grade attainable.

Where the ore is simple and the multi element analysis is favourable, simplified circuits such as single stage gravity separation or single stage high intensity magnetic separation can produce an acceptable concentrate from tailings at much lower capital and operating cost. Simplicity should be treated as a design objective, not as a compromise.

Matching Capacity, Feed Size and the Water Circuit

Once the flowsheet is fixed, equipment selection is a sizing exercise. Design capacity should carry a realistic margin above the plant's rated throughput, because titanium ores are often variable in hardness and grade. Feed size distribution must be matched to the separators: dry electrostatic units need a narrow, dry size band, magnetic separators need a defined top size to avoid matrix blockage, and flotation cells need deslimed feed. Water quality matters as much as water quantity, since high dissolved solids and process water recycled from thickeners can depress flotation and consume collector.

The commercial questions are equally concrete. Energy draw per tonne, consumable cost per tonne of concentrate, availability of spares in the region, and the ability to run units in parallel so that one failure does not stop the whole plant are usually more decisive than headline recovery figures from a single test. Modular and mobile units allow a project to start on a small footprint and scale as the resource is proven.

Material and Inspection Checks for Titanium Process Equipment

When the equipment itself is made of titanium, the selection criteria change completely. Grade selection follows the corrosion duty: Grade 2 for oxidising and general chloride service, Grade 7 where reducing conditions demand palladium stabilisation, Grade 12 where a molybdenum and nickel addition is used for higher strength in moderately reducing media, and Grade 9 where a higher strength tubing material is required. Tubular exchangers are normally ordered to ASTM B338 or ASME SB338, and plate fabrications to ASTM B265 or ASME SB265.

Inspection is where weak suppliers show themselves. Ask for a material certificate issued to EN 10204 3.1 that reports both chemistry and mechanical properties for each heat. Confirm that forming and welding were carried out with iron free tooling and cleaned surfaces, that welds were purged properly, and that the finished item passed a hydrostatic test and a dye penetrant or radiographic examination of the critical welds. Verify that the delivered heat numbers match the certificate before the equipment is installed, because a titanium exchanger that leaves the supplier with an unidentified heat cannot be repaired confidently in the future.

Frequently Asked Questions

Q: What is the first step in selecting titanium beneficiation equipment?
Determine the mineralogy and the liberation size of the ore. Every downstream decision, from grind size to separator type, follows from those two facts.

Q: Why is flotation used on the fines rather than gravity separation?
Gravity methods lose efficiency below roughly the fine sand range, where the density difference can no longer be exploited, while flotation chemistry works well on fine liberated particles.

Q: How do I choose between a high grade and a high recovery circuit?
Compare the value of the extra concentrate against the loss of recovered units and the added cleaning cost, then test both options against the specification of the consuming plant.

Q: Which titanium grade should be used for a chloride service heat exchanger?
Grade 2 to ASTM B338 is the normal starting point for oxidising and general chloride service, moving to Grade 7 where reducing conditions are present.

Q: What documents should accompany titanium process equipment?
A heat by heat material certificate to EN 10204 3.1 with chemistry and mechanical results, welding procedure and welder qualification records, and the reports from pressure and non destructive testing.

Q: Can a simplified circuit be justified for tailings retreatment?
Yes. Where multi element analysis shows a simple assemblage, single stage gravity or single stage high intensity magnetic separation can deliver an acceptable concentrate at a fraction of the capital cost.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry