Oct 14, 2025 Leave a message

ASTM B861 Grade 2 Pipe and Gr 5 Titanium Seamless Pipe

GR1 products provided by Henan Gnee New Material Co., Ltd

Gr2 Titanium Foil

Gr2 Titanium Wire

Gr2 Pure Titanium Bar

GR2 Titanium Straight Tube

Gr 2 Pure Titanium Plate

 

ASTM B861 Grade 2 vs Grade 5 Titanium Seamless Pipe

ASTM B861 (ASME SB861) is the standard specification for seamless titanium and titanium-alloy pipe. Within it, Grade 2 and Grade 5 answer two fundamentally different design questions: Grade 2 delivers corrosion resistance, formability and weldability at moderate strength; Grade 5 (Ti-6Al-4V) delivers structural strength for load-bearing systems. This guide compares the two and explains when to specify each.

 

1. Grade Designations and Chemistry

Element (max, %) Grade 2 (UNS R50400) Grade 5 (UNS R56400)
Titanium Balance Balance
Aluminum - 5.5 – 6.75
Vanadium - 3.5 – 4.5
Iron 0.30 0.40
Oxygen 0.25 0.20
Carbon 0.08 0.08
Nitrogen 0.03 0.05
Hydrogen 0.015 0.015

Grade 2 is a commercially pure (CP) alpha titanium; Grade 5 is an alpha-beta alloy strengthened by aluminum (alpha stabilizer) and vanadium (beta stabilizer).

 

2. Mechanical Properties (Annealed, B861)

Property Grade 2 Grade 5
Tensile strength, min 345 MPa (50 ksi) 895 MPa (130 ksi)
Yield strength (0.2% offset), min 275 MPa (40 ksi) 828 MPa (120 ksi)
Elongation in 50 mm, min 20% 10%

pure titanium

3. Corrosion Resistance

Both grades rely on the same self-healing TiO₂ passive film and therefore show similar resistance in the media where titanium excels: seawater, chloride brines, wet chlorine, nitric acid, organic acids and salt spray. Neither grade is suitable for hot reducing acids such as hydrochloric, hydrofluoric or sulfuric acid at high concentration, and titanium must not be used in aqua regia, which attacks it severely. Where reducing or crevice-corrosion service is unavoidable, Pd-bearing Grade 7 or Mo–Ni Grade 12 should be considered instead.

 

4. Forming, Welding and Fabrication

Grade 2 is highly ductile (20% minimum elongation), easy to bend, roll and weld with standard GTAW procedures and matching filler (ERTi-2), and is the default CP grade for pipe spools, coils and heat-exchanger tube. Grade 5 offers roughly 2.6 times the yield strength but only 10% elongation: it is stronger but stiffer, harder to cold-form, more prone to springback, and welding requires low-energy procedures with ERTi-5 filler and strict shielding to preserve joint ductility. For pressure piping, Grade 5 is usually supplied annealed; solution-treated-and-aged pipe is specified only where the design fully accounts for reduced weld-zone ductility.

 

5. Applications

Grade 2 seamless pipe: chemical process piping, seawater and desalination systems, heat exchangers and condensers, pulp-and-paper bleach plant piping, food and pharmaceutical process lines.

Grade 5 seamless pipe: structural and load-bearing tubing, aerospace hydraulic and structural lines, marine propulsion shafting applications, high-pressure and high-vibration systems where strength dominates.

 

6. Available Sizes

Parameter Grade 2 / Grade 5 Seamless Pipe
Outside diameter 4 – 219 mm (larger by special order)
Wall thickness 0.5 – 20 mm
Length Single random, double random, or cut length
Delivery condition Annealed (standard); cold-worked and stress-relieved; beta-transformed; solution-treated and aged (Grade 5)
Tests Tensile, flattening, bend, hydrostatic, eddy-current (as required)

 

7. Selection Summary

Choose Grade 2 when corrosion resistance, formability and weldability are the priorities and design pressures are moderate - the vast majority of chemical and marine piping applications. Choose Grade 5 when the design is strength-limited: thinner walls for the same pressure, higher allowable stress, or structural tubing that must carry mechanical loads. When in doubt, confirm the service medium, temperature, pressure and fabrication requirements with the supplier, because the corrosion advantage of titanium is always media-specific.

 

Titanium products provided by Henan Gnee New Material Co., Ltd

titanium pipe/tube

Material
Pure titanium and Titanium alloy
 
 
Titanium Grade
Grade 1-Unalloyed titanium
Grade 2-Unalloyed titanium
Grade 3-Unalloyed titanium
Grade 7-Unalloyed titanium plus 0.12 to 0.25 %palladium
Grade 9-Titanium alloy (3 % aluminum, 2.5 % vanadium)
Grade 12-Titanium alloy (0.3 % molybdenum, 0.8 % nickel),
Standard
ASTM B338/ASME SB338, ASTM B337/ASME SB337, ASTM B861/ASME SB861, ASTM B862/ASME SB862,AMS4911,AMS4928
Shape
Round Square Rectangle
Type
Seamless/Welded
 
 
Processing
Seamless titanium tube: Titanium sponge-Compacting electrodes-melting-Forge-Bar billets-Extruding-Rolled-Straightening-Seamless tube
Welded titanium tube: Titanium sponge-Compacting electrodes-melting-Forge-Plate billets-Hot rolled-Cold rolled-Titanium scrap-Welded-Welded tube
Surface
Polishing, picking, acid washed, black oxide
 
 
Application
1) Heat Exchanger, Condensers, Water Treatment, Desalination
2) Fluid, gas and oil transport
3) Pressure and heat transmission
4) Construction and ornament
5) Motorbycle and bike
Material Milling Certificate
According to. EN 10204.3.1
Including Chemical composition and Mechanical property

Get the latest quote

 

 

titanium rod/bar

Product name

Pure Titanium bar/Pure Titanium rod/Titanium alloy bar/Tianium alloy rod

Standard

GB/T 2965-2007 GB/T 13810-2007, ASTM B348,ASTM F67,ASTM F136, AMS4928,MIL4911

Titanium type

Commercially Pure(CP) / Titanium alloy

Grade

TA1 TA2 TA3 TA4 TA5 TA6 TA7 TA8 TA9 TA10 TA11 TA12 TA13 TA14
TA15 TA16 TA17 TA18 TA19 TA20 TA21 TA22 TA23 TA24 TA25 TA26
TA27 TA28
GR1 GR2 GR3 GR4 GR5 GR6 GR7 GR9 GR12 GR16

Diameter

3-350mm

Length

Max6000mm

Technique

Forging, machining

Surface

Acid surface or polishing, sand blasted surface

Shape

Round, flat, square, hexagonal

Application

Metallurgy, electronics, medical, chemical, petroleum, pharmaceutical, aerospace, etc.

Get the latest quote

 

 

titanium plate/sheet/strip

Item

Titanium plate,Titanium sheet

Grade

GR1,GR2,GR5,GR7,GR9,GR12,GR23,etc.

Size

0.3-3mm≤1000-1500mm≤12000mm or as your request

Standard

ASTM B265, ASME SB265,AMS491

Material

pure titanium ( gr1, gr2, gr3,,gr4)

Titanium Alloy(GR5, GR7,GR9,GR23,TI-6AL-7NB)

Ti-6Al-2Sn-4Zr-2Mo, Ti-6Al-2Sn-4Zr-6Mo

Ti-V(15wt%)-Cr(3wt%)-Sn(3wt%)-Al(3wt%)

Quality and test

Hardness test, Bending test, Hydrostatic etc.

Application

chemical, industry, sports etc.

Feature

High corrosion resistance, low density, good thermal stability

Technics

Hot rolled,Cold Rolled

Surface

Bright, Polished, Pickling, Acid cleaning, Sandblasting

Get the latest quote

 

 

titanium wire

item

Titanium wire

Grade

Gr1, Gr2, Gr3, Gr4, Gr5, Gr7, Gr9,, Gr23, etc.

Millimeter(mm)

0.8mm - 6.0mm

Technology

Hot-Rolled, Cold-Rolled, Hot forging , Machining

Standard

ASTM B265, AMS 4911, AMS 4916, ASTM F67, ASTM F136,AWS A5.16

Condition

Cold rolled(Y), Hot rolled(R), Annealed (M), Quenching(C)

Shape

Straight, Spool, Coil

Surface

Acid Washed, Polished surface, Grinding Polished

Advantage

1.Low Density and High Specification Strength
2.Excellent Corrosion Resistance
3.Good resistance to effect of heat

4.Excellent Bearing to cryogenic property
5.Nonmagnetic and Non-toxic
6.Good thermal properties
7.Low Modulus of Elasticity

Application

Military,Medical, Industry,Glasses,Jewelry, Ornaments,welding,Sporting goods,Motor vehicle,Electroplating

Delivery Time

Within 7-15 Days

Get the latest quote

 

 

 

Send Inquiry

whatsapp

Phone

E-mail

Inquiry