Oct 13, 2025 Leave a message

GR1, GR2, GR5, GR9 Titanium Pipe and Tube Selection Guide

Standards That Govern Titanium Pipe and Tube

Titanium tubular products are ordered against distinct specifications depending on the product and the service. ASTM B861 covers seamless titanium and titanium alloy pipe, ASTM B862 covers welded titanium pipe, ASTM B338 covers seamless and welded tube for condensers and heat exchangers, and ASTM B337 covers welded titanium tube. The ASME equivalents, SB861, SB862, SB338 and SB337, apply when the component is designed to the ASME pressure vessel and piping codes. The GB equivalents are GB/T 3624 for seamless tube and GB/T 3625 for welded tube.

Standard Product Typical service
ASTM B861 / ASME SB861 Seamless pipe Process piping, high pressure lines
ASTM B862 / ASME SB862 Welded pipe Larger diameter, lower pressure lines
ASTM B338 / ASME SB338 Seamless and welded tube Heat exchangers, condensers
ASTM B337 / ASME SB337 Welded tube Heat exchangers, condensers
GB/T 3624 and GB/T 3625 Seamless and welded tube General industrial service

Grade Chemistry

Element, max unless stated GR1 GR2 GR5 GR9
Carbon 0.08 0.08 0.08 0.08
Iron 0.20 0.30 0.30 0.25
Hydrogen 0.015 0.015 0.015 0.015
Nitrogen 0.03 0.03 0.03 0.03
Oxygen 0.18 0.25 0.20 0.15
Aluminium - - 5.5 to 6.75 2.5 to 3.5
Vanadium - - 3.5 to 4.5 2.0 to 3.0
Titanium Balance Balance Balance Balance

Grade by Grade Selection

Grade UNS Minimum tensile strength Minimum yield strength Why it is chosen
GR1 R50250 240 MPa 170 MPa Maximum formability and weldability, tight radius bending, expanded joints
GR2 R50400 345 MPa 275 MPa General corrosion duty with a useful strength margin; the workhorse grade
GR5 R56400 895 MPa 828 MPa High strength and fatigue resistance where weight and section size must be minimised
GR9 R56320 620 MPa 483 MPa Strength between GR2 and GR5 with better formability than GR5

GR1 and GR2 are unalloyed and are chosen for corrosion duty; GR5 is an alpha-beta alloy chosen for load; GR9, the Ti-3Al-2.5V alloy, occupies the middle ground and is widely used for hydraulic tubing where a combination of moderate strength, fatigue resistance and formability is required. Where reducing acids are involved, palladium or molybdenum bearing grades replace GR1 and GR2 rather than a higher strength grade.

Service Environments and Application Notes

In chemical plant, GR2 pipe and tube carry chlorides, hypochlorite, nitric acid and organic media, and GR2 tube handles most heat exchanger duties where the process side is oxidising. In marine and desalination service, GR2 and GR1 tube are used for condensers, brine heaters and seawater lines because copper alloys suffer erosion corrosion and stainless steels pit in chlorides. In power generation, titanium tube is standard for seawater cooled condensers and for cooling water systems in coastal stations.

In aerospace and defence, GR9 tube is used for hydraulic lines because it gives roughly twice the strength of GR2 with better formability than GR5, while GR5 is selected for structural tube and high pressure fittings. In medical and food service, GR1 and GR2 are used for their inert, cleanable surfaces, and in electroplating and chemical recovery the same grades are used for heating coils and anodes. Where a line carries a reducing acid, a palladium or molybdenum bearing grade such as GR7 or GR12 replaces GR2 rather than a higher strength grade.

Size Range, Delivery Condition and Testing

Pipe is typically supplied from 1/2 inch nominal bore to 24 inch nominal bore in schedules from SCH10 to SCH XXS, and tube from about 1 mm outside diameter to 254 mm outside diameter with wall thickness from 0.1 mm to 20 mm. Forms include seamless, ERW, welded and fabricated, with round, square, rectangular and oval sections; ends are plain, beveled or threaded, and lengths are random or fixed.

Delivery condition is normally annealed and pickled, or bright annealed for tube. Testing and documentation commonly include chemical analysis, tensile and hardness testing, flattening and flare testing, hydrostatic or pneumatic pressure testing, eddy current examination, positive material identification and, where specified, intergranular corrosion and pitting resistance testing. Mill test certificates are issued to EN 10204 3.1, and third party inspection can be arranged for project orders. Packing is in wooden boxes or bundled with strips, with plastic end caps and grade marking on each bundle.

Frequently Asked Questions

Q: What is the difference between ASTM B861 and ASTM B338?

A: B861 covers seamless pipe and B338 covers seamless and welded tube; pipe is ordered by nominal bore and schedule while tube is ordered by outside diameter and wall thickness, and the two are used for different pressure and heat transfer duties.

Q: Which grade is best for seawater piping?

A: GR2 is the standard choice for seawater and chloride service, with GR7 or GR12 selected where reducing acids or higher temperatures are present.

Q: Can GR5 tube be welded in the field?

A: Yes, with inert gas shielding and appropriate filler, but the alloy is less tolerant than GR2 and requires controlled welding parameters and post weld inspection to confirm no oxygen contamination.

Q: Are welded and seamless pipe interchangeable?

A: Not automatically. Welded pipe is available in larger diameters and thinner walls, but the design must account for the weld and the applicable code requirements, so the purchase order should state the type required.

Q: What certificates are provided with titanium pipe and tube?

A: A mill test certificate to EN 10204 3.1 with chemical and mechanical results, plus the specific test reports required by the order such as eddy current, hydrostatic pressure, positive material identification and third party inspection.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry